Technician testing a gas furnace burner with a multimeter

Furnace Repair

Furnace clicking, lighting and shutting off? Track down the failed part and get steady heat back without guessing.

  • Ignition, blower and venting faults
  • Gas and oil furnaces
  • Repair and replacement prices compared
Call (551) 266-2563

Furnace Repair Paramus

With most homes in Paramus, New Jersey heating with natural gas, the forced-air gas furnace is the system behind most winter calls. These furnaces run through the same sequence every time they start: the inducer fan clears the flue, a pressure switch confirms the draft, the igniter heats up, the gas valve opens and the flame sensor proves the flame. A failure at any step stops the furnace.

Furnace repair means finding which step failed. The control board usually flashes a code that points in the right direction, and the contractor confirms it with a meter before replacing anything.

Ignition, Blower and Flame Problems

  • Flame lights, then drops out: dirty flame sensor or poor ground.
  • No glow from the igniter: cracked hot-surface igniter or no signal from the board.
  • Inducer runs, nothing else happens: blocked vent, failed pressure switch or cracked hose.
  • Blower squeals or won't run: worn motor, failed capacitor or a broken belt on older units.
  • Burning smell after the first start of the season: usually dust on the heat exchanger; a smell that lasts needs a check.

Gas furnace repair and oil furnace repair share the blower and controls, but oil burners add a nozzle, a filter and electrodes that need cleaning each year.

For air conditioning and other equipment, see HVAC system repair.

Furnace Replacement: When Repairs Stop Making Sense

A cracked heat exchanger, a failed control board on a unit past 20 years, or a third repair in two winters all point toward replacement. Furnace installation of a high-efficiency model often means new PVC venting out the side of the house, because those furnaces can't vent into an old masonry chimney.

Replacing a furnace with one of the same capacity is minor work under the New Jersey construction code: the Paramus Building Department needs notice before work starts and a permit application. Gas furnace replacement that changes the size or the venting can need a full permit.

If you smell gas near the furnace:

  1. Leave the house right away and take everyone with you.
  2. Don't touch light switches, the thermostat or anything that could spark.
  3. From outside, call PSE&G's gas emergency number, 1-800-880-7734, or 911.

Gas or Oil?

Gas furnaces are the norm locally, and oil furnaces are now uncommon. Oil systems need yearly cleaning to stay reliable, and an oil burner that soots up will lock out more often. If an oil furnace is near the end of its life, it's worth getting a price for a gas or heat pump replacement at the same time as the repair quote.

How Much Should You Budget?

Most furnace repairs cost about $150 to $1,200. A flame sensor cleaning or a new igniter sits near the low end; an inducer motor, blower motor or control board lands toward the top.

Furnace services on a weekend or overnight usually carry a higher service charge, so ask about it up front when you call (551) 266-2563.

Before the Contractor Arrives

  1. Note any blinking light code on the furnace control board.
  2. Check that the furnace switch, which looks like a light switch, is on.
  3. Replace the filter if it's clogged.
  4. Clear stored boxes away from the furnace so it can be reached.

Questions About Warm-Air Systems

Why does my furnace keep shutting off after it lights?

A dirty flame sensor is the most common cause. The furnace can't prove the flame, so it shuts the gas off for safety.

How much does furnace repair cost in Paramus, NJ?

Most furnace repairs cost about $150 to $1,200, depending on the part.

Can a cracked heat exchanger be repaired?

Generally no. A cracked heat exchanger can leak combustion gases, and most manufacturers and contractors treat it as a reason to replace the furnace.

Does replacing a furnace need a permit in New Jersey?

Yes. A same-size replacement is minor work, which needs notice to the building department and a permit application.

What does the blinking light on a furnace mean?

It's a fault code from the control board. The chart is usually on the inside of the furnace door.

Get Heat Moving Again

Most furnace problems come down to one part in the start-up sequence. Call and read off any light code on the board.

Call (551) 266-2563